VA, watts and the 0.6 surprise on the box
Indian shops still sell most standby and line-interactive UPS units in VA, not in watts. A very common label is “600 VA / 360 W”. That second number is the one your gaming PC cares about. It is the first number multiplied by a power factor that manufacturers often take as 0.6 for this class of product. If your PC pulls 300 W from the wall while you play, a 600 VA / 360 W brick has only 60 W of spare room before it either beeps, switches to battery early or shuts down.
This sizer starts from wall-draw watts — the same kind of figure the electricity-bill tool wants — and applies headroom. Twenty-five per cent is a reasonable default: fans speed up, a game compiles shaders, Windows decides to index a drive. Design load = watts × (1 + headroom). Required VA at a 0.6 power factor = design load ÷ 0.6. For 300 W and 25 per cent headroom that is 375 W and 625 VA, so the page recommends the next common class, 1,000 VA, not a 600 VA unit that only looks cheaper.
Do not size from the power supply’s rated wattage. A 750 W Gold unit on a 1080p machine might see 280 W at the wall. Putting “750” in the box will push you toward an expensive inverter you do not need for short cuts, while still saying nothing about runtime. If you do not know wall draw, estimate from the electricity tool’s presets or from a plug meter, then come back here.
Pure sine wave, Active PFC and long Indian outages
Almost every modern gaming power supply uses Active Power Factor Correction. Many of those units expect a sine-shaped mains waveform. Cheap stepped-sine or “simulated sine” UPS units output a square-ish wave that can make such a PSU buzz, refuse to start or run hot. The safe rule, which this page prints next to every result, is to pick a UPS or home inverter that advertises a pure sine-wave output when the load is a gaming PC. Brand marketing pages from APC, Microtek and others repeat the same caution for sensitive or PFC loads; treat it as electrical compatibility, not as a sales upsell.
Runtime is a separate question from VA class. A typical small UPS battery is a single 12 V, 7 Ah sealed lead-acid brick, about 84 Wh on paper and far less once you count inverter efficiency and the fact that you should not empty a lead-acid battery every afternoon. A rough check is (battery watt-hours × 0.6 efficiency ÷ PC watts) × 60 minutes. That is why a living-room gaming load often gets five to fifteen minutes on a desktop UPS — enough to save and shut down, not enough to finish a ranked match through a two-hour cut.
When the cut regularly lasts longer than a cup of tea, Indians usually move to a home inverter and a larger battery (the Luminous, Microtek, Exide kind of shopping). The inverter still needs a watt rating above your design load and, again, a pure-sine output if the PSU is picky. The PC should sit on a dedicated socket that does not share a cheap extension board with a refrigerator compressor. This tool’s second paragraph of result text switches tone once the load crosses about 450 W, because that is where “buy a slightly bigger UPS” stops being the whole answer.
What this page will not do
It will not pick a SKU for you or promise that a particular 1 kVA model will run your exact tower for 22 minutes. Battery age, temperature, cable losses and the rest of the house load all change runtime. It will not tell you to run a mining rig or a second-hand server off a thin UPS. It will not replace an electrician if your building’s earthing is poor — a UPS is not a fix for a dangerous mains outlet.
Use it as a filter. If the suggested class is 1,000 VA and the shop is waving a 600 VA box because it is on discount, you now have the arithmetic to walk away. If you also opened the full-set budget planner, put the rupee cost of that UPS in the reserve line so the tower budget stays honest. If you opened the electricity-bill tool, you already know that long inverter runtime has its own monthly cost in battery wear and extra kWh.
Everything runs in the browser. The numbers are illustrations from your inputs. For a named build, measure wall draw once, then size. That single measurement is worth more than any default we could ship.