How to test a controller in your browser
Plug your controller in with a USB cable or pair it over Bluetooth, open this page and press any button — browsers only reveal a gamepad after the first press, for privacy. The page then shows the controller’s name, whether it uses the standard layout, how many buttons and axes it reports and whether rumble is available. Every button lights up when pressed; analog triggers fill up gradually so you can see the exact pressure from 0 to 100%. Each stick is drawn as a circle with a live dot, a trail of recent positions and the numeric X and Y values to three decimals. It works with Xbox One, Xbox Series, PlayStation 4 DualShock, PlayStation 5 DualSense, Switch Pro, 8BitDo, and most generic USB and Bluetooth pads, in Chrome, Edge, Firefox and Safari.
Pick the label style that matches your controller — Xbox (A B X Y), PlayStation (✕ ○ □ △) or Switch — and the buttons are named accordingly. If the page says non-standard mapping, the browser could not match your controller to the standard layout; buttons are then shown by number, and their order depends on the maker.
The 5-second stick-drift test
Stick drift is when your character walks or the camera turns on its own, without you touching the stick. It happens because the potentiometers or sensors inside the stick wear out or get dirty, so the stick reports a position that is not quite centre. To test it, put the controller on a flat table, press 5-second drift test and take your hands off. The page samples both sticks every frame for five seconds and reports, for each stick:
- Maximum offset at rest — the furthest the stick reported from centre, as a percentage of full tilt. This is the number that matters.
- Average offset and the centre point — useful to see whether the stick drifts in one direction or jitters around.
- A verdict: under 5% is “no drift”; 5–10% is slight and is hidden by the default deadzone in most games; 10–20% is noticeable drift; above 20% is severe.
- A suggested deadzone — the smallest in-game deadzone that will hide what was measured (maximum offset plus a 2% margin). Most PC and console games have a deadzone slider in their controller settings; set it to this value instead of guessing.
Run the test two or three times. Drift often comes and goes; the highest reading is the honest one. Also flick each stick and let it snap back, then run the test again: a stick that returns to a different centre each time has a worn spring or sensor.
The circularity test
A healthy stick should reach full tilt in every direction. Press Circularity test and slowly roll each stick around its outer edge three times. The page records the furthest point reached in each of 36 directions and reports the average circularity error — how far, on average, those points are from a perfect circle — and the coverage, the share of directions you reached. Many controllers have a square-ish outer gate and read a few percent past the circle on the diagonals, so an error of 5–15% is normal; a much higher number, or a flat spot where one direction never reaches full tilt, means the stick will not let you run at full speed or aim precisely in that direction. The trail drawn on the stick circle shows the shape directly.
Triggers, buttons and rumble
Press each trigger slowly to the bottom. The trigger range line records the maximum each trigger reached; a trigger that never reaches 100% may not fire fully in racing games or shooters. Each button also counts presses — tap a suspect button 20 times and check that the counter says 20. A higher count means the button is double-firing; a lower count means it is missing presses.
The rumble buttons play a short vibration on both motors, only the strong (left, low-frequency) motor or only the weak (right, high-frequency) one. Trigger rumble drives the impulse triggers on Xbox One and Series controllers in browsers that support it (Edge and Chrome on Windows). PlayStation’s adaptive triggers and haptics are not available to web pages, and some browsers or Bluetooth connections do not expose rumble at all — the page says so rather than failing silently.
What to do if your controller drifts
- Recalibrate and update. Update the controller’s firmware (Xbox Accessories app, PS5 settings) and, on PC, check Windows’ “Set up USB game controllers” calibration or Steam’s controller calibration.
- Raise the deadzone. Use the suggested deadzone from the test in each game. It is a workaround, not a cure, but it often makes a mildly drifting stick usable again.
- Clean it. Power the controller off, tilt the stick fully and blow compressed air around the base while rotating it. Some players use a little isopropyl alcohol; do this at your own risk and never on a powered device.
- Warranty and repair. Drift is a known wear issue. Within warranty, contact Sony or Microsoft support; outside it, stick modules can be replaced by repair shops, and Hall-effect sticks, which use magnets instead of contact tracks, are far less prone to drift.
Troubleshooting connection
- Nothing happens: press a button (not just a stick), and make sure no other app — Steam Big Picture, DS4Windows, a game — has grabbed the controller exclusively.
- PS5 DualSense on Windows: works over USB and Bluetooth in Chrome and Edge; if only some buttons work, try the USB cable.
- Several controllers: each one appears in the controller list; pick the one to test. Press a button on each to wake it up.
- Phones: Android with Chrome supports USB-OTG and Bluetooth controllers. iPhone and iPad support Xbox, PlayStation and MFi controllers in Safari.
Privacy and offline use
All readings stay in your browser; nothing is uploaded, and no account is needed. The controller name the browser reports is shown only on your screen. Use Copy report to paste your results into a warranty claim or a message to a seller. Install the page as an app from the browser menu, and it will open even without internet.
Sources and standards
- W3C, Gamepad specification — the “standard” button and axis mapping (buttons 0–16, axes 0–3) used for the labels on this page.
- MDN Web Docs, Gamepad API and GamepadHapticActuator (dual-rumble and trigger-rumble effects).
- Sony Interactive Entertainment, PlayStation hardware support — DualSense and DualShock repair and warranty.
- Microsoft, Xbox Wireless Controller support — connecting over USB and Bluetooth, and controller troubleshooting.
- Valve, Steam Input for developers — how games apply deadzones and outer-range settings.
Frequently asked questions
How do I test for stick drift?
Connect the controller, press a button, put it on a flat table and press 5-second drift test without touching it. Under 5% is no drift; 5–10% slight; 10–20% noticeable; above 20% severe.
What deadzone should I use?
Use the suggested deadzone from the drift test — the maximum offset measured at rest plus a 2% margin. Set it in each game’s controller settings.
Does it work with a PS5 DualSense or PS4 controller?
Yes, over USB or Bluetooth in Chrome, Edge, Firefox and Safari. Pick PlayStation labels to see ✕ ○ □ △. Adaptive triggers are not available to web pages.
Why is my controller not detected?
Press a button — browsers hide gamepads until the first press. Close apps like Steam Big Picture or DS4Windows that may hold the controller exclusively, and try a USB cable.
What does circularity error mean?
How far the stick’s outer edge is from a perfect circle, averaged over 36 directions. 5–15% is typical because many sticks have a square-ish gate; flat spots are a problem.
Can I test rumble?
Yes, if your browser and connection support it. Both motors, the strong or the weak motor, and Xbox trigger rumble can be tested separately.
Is anything uploaded?
No. All readings stay in your browser and nothing is stored after you close the page.